'; ?>

Search:

Type: Posts; User: Zelephant

Page 1 of 18 1 2 3 4

Search: Search took 0.04 seconds.

  1. Are those diodes possibly ballast resistors or...

    Are those diodes possibly ballast resistors or maybe capacitors for the coils ?? And have you checked the fuel pump relay or connected12v direct to fuel pump... Just guessing..!???.
  2. Replies
    2
    Views
    1,471

    Why not have a new post subject. VOICE OF THE...

    Why not have a new post subject.
    VOICE OF THE LAMS.
  3. Replies
    5
    Views
    3,076

    Memories

    Meeting my future wife to be.... Taking her home on my 900 bol dor helmetless.

    Better memory... Divorcing her !
  4. Thread: Airhawk

    by Zelephant
    Replies
    6
    Views
    1,691

    For any geriatrics that gives a ****... Santa was...

    For any geriatrics that gives a ****... Santa was kind.
    Put the Airhawk on the old girl this morning and did a1.5 hr blast...big big difference for an older Zelephant with a dodgy hip and knee....
  5. Thread: Airhawk

    by Zelephant
    Replies
    6
    Views
    1,691

    Thanks mate.... Is he a browibro... That could...

    Thanks mate....
    Is he a browibro...
    That could go into the Webster genealogical definition section...phew!
  6. Thread: Airhawk

    by Zelephant
    Replies
    6
    Views
    1,691

    Airhawk

    Anyone tried the Airhawk cushion on a1980 kz1000.
  7. Replies
    2
    Views
    2,658

    How about Melbourne... The tigers will lick ya...

    How about Melbourne...
    The tigers will lick ya wounds..
  8. Replies
    2
    Views
    1,091

    Is it wired directly to the battery ??... If so...

    Is it wired directly to the battery ??... If so it may be inhibiting the charge rate to the battery.
    Hook it up to a 12 volt supply which will only work with ignition on.. Headlight maybe??.
  9. Replies
    9
    Views
    2,635

    Lol

    Lol
  10. Replies
    9
    Views
    2,635

    Dumb question...?. Why would only one valve seat...

    Dumb question...?.
    Why would only one valve seat "run out of meat"...
    and not more ? Exhaust or inlet ?
    Can you not just grind the valve stem to give shim variances to play with..???.

    Smart...
  11. Replies
    9
    Views
    2,635

    Valves can vary greatly...depending on which head...

    Valves can vary greatly...depending on which head you want to use..
    I guess there's a reason for bigger or smaller valves..??

    WHY?.
  12. Replies
    4
    Views
    2,181

    3pins

    Could the 3 pin connector come from the alternator and somehow plug into or near the rectifier..???.
  13. Replies
    13
    Views
    3,247

    Great color..matches the streletsia and...

    Great color..matches the streletsia and cordyline. ��
  14. Replies
    4
    Views
    1,598

    What happened?.

    What happened?.
  15. Replies
    4
    Views
    1,598

    Had a GS 1000s. Did lots of work to it and after...

    Had a GS 1000s.
    Did lots of work to it and after 50 or so km it just stopped while sitting at traffic lights.
    After a long push back to my mates ...rocker cover off...cam sprocket bolt...
  16. Replies
    13
    Views
    3,247

    Good old aussie ingenuity. Where there's a will...

    Good old aussie ingenuity.
    Where there's a will there's a way.
  17. Replies
    19
    Views
    4,336

    Could be one...could be the other...I had a cb900...

    Could be one...could be the other...I had a cb900 bol dor when I was a lad....it didn't like first gear at high revs..
    Sounds the same and the crank shaft w
    as destroyed.
    Hope it's only a clutch...
  18. Replies
    19
    Views
    4,336

    Get a big screwdriver...put handle to your ear...

    Get a big screwdriver...put handle to your ear and pointy end at various locations on the engine.
    This works like a stethoscope....could be bottom end...conrod bearing shells....just guessing.
    ...
  19. Replies
    9
    Views
    1,535

    Sticky tape

    Sticky tape
  20. Replies
    9
    Views
    1,535

    Google..(easy out).. Fiddly but worth the...

    Google..(easy out)..
    Fiddly but worth the effort.
    Or drill and helicoil.
  21. Pitty about the viv issues.. nothing beats a...

    Pitty about the viv issues.. nothing beats a naked bitch.
  22. Replies
    27
    Views
    5,569

    So how were your friction plate measurements.

    So how were your friction plate measurements.
  23. Replies
    27
    Views
    5,569

    Z1000 st shaft drive. Each plate..min thickness...

    Z1000 st shaft drive.
    Each plate..min thickness 2.7mm..replace...over that re use. Your choice.
    Chain drive 3.5mm min thickness.
    Good luck mate.
  24. Replies
    12
    Views
    4,112

    Sticky: No it wasn't...but now that you mention it......

    No it wasn't...but now that you mention it... Maybe.
  25. Replies
    12
    Views
    4,112

    Sticky: Well done admin.

    Well done admin.
Results 1 to 25 of 448
Page 1 of 18 1 2 3 4
Powered by vBulletin® Version 4.1.12
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
Extra Tabs by vBulletin Hispano
All times are GMT +10. The time now is 01:02 PM.
vBulletin 4.0 skin by CompleteVB
Your continued use of this forum constitutes your acceptance of the Forum Rules and Terms and Conditions.